Amber Silver Bullets on the front forks


Red Silver Bullets on the rear fender struts


LED Mini-Bullets (grooved shown)

Silver Bullet L.E.D. Signal Lights - All new L.E.D. Silver Bullets. Beautifully chromed Silver Bullets feature a distinctive, slotted bezel with clear lenses. The CAD designed lenses enhance the already bright L.E.D. output to provide exceptional, jewel-like illumination.

These are two-circuit lights, and can be wired to operate as motorcycle turn signals with dual functions like "run-signal", "run-brake", signal-brake", etc. These lights come with an extra trim ring for a different look, as well as the load equalizer to keep your signals flashing at the correct rate (you don't need to buy the equalizer separately!).

See the mounting kits and info in the 'Mounting Hardware' section below, for alternative mounting methods on your bike.

##16-201A Mini Markers


##16-107A LED Marker Lights


##25-9501B LED Marker Lights

Marker and Mini-Marker Lights and Signals - These lights are universal mount, and can be used for cornering lights, mini-signals, functional replacements for reflectors, etc.

#16-111 Starburst Series Lighting


#16-113 Eagle Eye Series Lighting

NEW LED Lighting Units by Show Chrome - These lights are universal mount mini-signals and marker lights. A compact, inexpensive, and bright custom lighting alternative with low power drain!

Hollow Mounting Stud for concealed wiring




P-Clamp Style Mount




Clamshell type mounting




Two-Piece Fork Mount

Mounting Hardware, clamps, and Custom Mounts for Lights and Signals - These mounting products can be combined with the various lights, mini-signals, spots, etc. on this page for installation on your bike.

Before you order, read these notes to help with your selection of mounting hardware:

- The Hollow Stud Mounting kits allow installation via fender rail bolts, where the wire is totally concealed within the light and mount. The hollow mounting stud replaces the rear fender rail bolt, and provides a threaded stem for the light to attach. The wire passes through the center of the stud and under the fender, completely invisible from the outside. These are available in two sizes: 8mm diameter mounts (like those used on the Honda Ace 750, Kawasaki Vulcan 800/1500, etc), and 10mm diameter mounts (for mounting on the Honda Spirit 750 and other bikes with m10x1.25 fender rail bolts).

- The P-clamp Mounting kits allows the installation of lights on un-shrouded front forks (like those on the Honda 750 Spirit), etc. Note that the P-Clamp mounts may require the mounting hole to be enlarged with a drill, depending on the light attachment hardware.

- Clamshell Mounts are a very universal mounting method, and accomodate nearly every type of light. They are a bit more robust, and a good choice when attaching large spotlights, 50 watt Halogen lamps, etc.

- Two-Piece Fork Mounts are best for applications where the wiring exits the light housing, not from within a hollow mounting stud. - The small diameter vertical section of the F&S Engine guards (nearest the frame) for the Vulcan 800 and 1500 Classic are 1" diameter.

- The small OEM engine guards on the V-Star 650 is 1" diameter.

- The 1" diameter clamp makes a great 1" handlebar mount for speakers, tachometers, GPS, etc.

- Cobra and MC Enterprises engine guards are 1-1/4" diameter.

- Frame down tubes on a V-Star 650 and 1100 are 1-1/4" in diameter.

- Frame down tubes on most Vulcan's and Honda Cruisers are 1.35" diameter.

LED Taillight Insert- This LED board plugs right into the stock socket, replacing the original light bulb. Provides RUN, STOP, and License plate light. Use your existing Lens and Light Bucket and pack 136 RED LEDs PLUS 3 SMT White LEDs for License plate illumination Comes! Supplied with a standard 1157 light bulb base attached to all wires for a simple plug-in installation. Less drain off the electrical system. Now people will be sure to see you stopping! Fits all Suzuki Volusia 800, Boulevard C50 & C50T, Intruder 1500 LC, and Boulevard C90 & C90T.

Tombstone Tail Light - Go back in time without giving up any modern conveniences. This new Tombstone Tail Light ( 4991/4992 with optional signals is shown to the left) provides old school styling with cutting edge L.E.D. technology, a finely chromed housing and rich, red lens. Hi-intensity L.E.D.s make sure you get noticed. More than just a tail light, the base incorporates a removable license plate bracket.

The #4990 Universal Tombstone is a Taillight only, it does not incorporate turn signal mounting bar/base plate. Intended for use in custom applications, mounting and wiring holes must be drilled for installation. It looks like the #4491 and #4992 on the left, without the turn signal mounting bar/base.

#4804 (l) & #4803 (r)

Tru-Sphere L.E.D. Bulbs - These are the best L.E.D. replacement bulbs on the market. Each bulb features 32 mega-bright red or 32 super bright amber L.E.D.s in a completely sealed package. Tru-Sphere's unique design provides full hemispherical illumination; you won't believe the improvement over an incandescent bulb. It's dimensions are the same as a standard 1156 incandescent bulb so it can be used as a direct replacement for those applications.

Turn Signal, Tail Light, and Reflector Accents / Visors

Rear Signal Adapters-  Moves the rear flashers to the license plate bracket without original flasher arms, rail, fender or other bracket. Usually requires drilling new mounting holes to install. Sold in pairs.

Billet aluminum adapter replaces the OEM black arm and moves the flashers 1 3/8" closer to the bike. Sold in pairs.

Rear Signal Relocator Bars & Mounts - Moves the rear flashers to the license plate bracket.