Amber Silver Bullets on the front forks


Red Silver Bullets on the rear fender struts


LED Mini-Bullets (grooved shown)

Silver Bullet L.E.D. Signal Lights - All new L.E.D. Silver Bullets. Beautifully chromed Silver Bullets feature a distinctive, slotted bezel with clear lenses. The CAD designed lenses enhance the already bright L.E.D. output to provide exceptional, jewel-like illumination.

These are two-circuit lights, and can be wired to operate as motorcycle turn signals with dual functions like "run-signal", "run-brake", signal-brake", etc. These lights come with an extra trim ring for a different look, as well as the load equalizer to keep your signals flashing at the correct rate (you don't need to buy the equalizer separately!).

See the mounting kits and info in the 'Mounting Hardware' section below, for alternative mounting methods on your bike.

Iron Cross L.E.D. Light

Iron Cross L.E.D. Light - This L.E.D. Iron Cross light is great added visibility and old school style. This LED light functions as a run & brake light. It measures 4-1/2" x 5" and is 3/4" thick. Great for many custom applications.

##16-201A Mini Markers


##16-107A LED Marker Lights


##25-9501B LED Marker Lights

Marker and Mini-Marker Lights and Signals - These lights are universal mount, and can be used for cornering lights, mini-signals, functional replacements for reflectors, etc.

#16-111 Starburst Series Lighting


#16-113 Eagle Eye Series Lighting

NEW LED Lighting Units by Show Chrome - These lights are universal mount mini-signals and marker lights. A compact, inexpensive, and bright custom lighting alternative with low power drain!

Hollow Mounting Stud for concealed wiring




P-Clamp Style Mount




Clamshell type mounting




Two-Piece Fork Mount

Mounting Hardware, clamps, and Custom Mounts for Lights and Signals - These mounting products can be combined with the various lights, mini-signals, spots, etc. on this page for installation on your bike.

Before you order, read these notes to help with your selection of mounting hardware:

- The Hollow Stud Mounting kits allow installation via fender rail bolts, where the wire is totally concealed within the light and mount. The hollow mounting stud replaces the rear fender rail bolt, and provides a threaded stem for the light to attach. The wire passes through the center of the stud and under the fender, completely invisible from the outside. These are available in two sizes: 8mm diameter mounts, and 10mm diameter mounts (8mm and 10mm size refers to the diameter of the bolt shaft, not the head). This will allow fitment to all Victory motorcycles. Measure your fender rail bolt size before ordering.

- The P-clamp Mounting kits allows the installation of lights on un-shrouded front forks, etc. Note that the P-Clamp mounts may require the mounting hole to be enlarged with a drill, depending on the light attachment hardware.

- Clamshell Mounts are a very universal mounting method, and accomodate nearly every type of light. They are a bit more robust, and a good choice when attaching large spotlights, 50 watt Halogen lamps, etc.

- Two-Piece Fork Mounts are best for applications where the wiring exits the light housing, not from within a hollow mounting stud. - The 1" diameter clamp makes a great 1" handlebar mount for speakers, tachometers, GPS, etc.

- Cobra, MC Enterprises, and Linby engine guards are 1-1/4" diameter.

- Frame down tubes on most bikes are 1-1/4" in diameter.

Tombstone LED Tail Light


#9157 Matching Curved License Plate for #4992 above

Tombstone Tail Light - Go back in time without giving up any modern conveniences. This new #4990 Tombstone Tail Light provides old school styling with cutting edge L.E.D. technology, a finely chromed housing and rich, red lens. Hi-intensity L.E.D.s make sure you get noticed.

The #4990 Universal Tombstone is a Taillight only, it does not incorporate turn signal mounting bar/base plate as seen in the photo to the left. Intended for use in custom applications, mounting and wiring holes must be drilled for installation. It looks like the #4491 and #4992 on the left, without the turn signal mounting bar/base.

The #4992 Tombstone includes the turn signal mounting bar/base plate as seen in the photo to the left. Intended for use in custom applications, mounting and wiring holes must be drilled for installation.

Low Profile L.E.D. Taillight, Smoke Lens - This is a Low Profile L.E.D. Taillight Conversion with a Smoke Lens. Very bright! Each light includes connectors for '99-later and '98-earlier taillight bases. Fits: '89-'08 FXST (ex. Deuce), XL, '90-'08 FLSTF, Dyna, '89-'00 FXR.

Deluxe style LED Tail light, smoke lens - Our L.E.D. Conversions for incandescent taillights are as easy to install as changing a bulb. We mount our L.E.D. circuit boards inside our stylized lenses so all you have to do is take off your boring stock lens, remove the bulb, plug our connector into the socket and install our lens. Very bright! Each light includes connectors for '99-later and '98-earlier taillight bases. Fits: '89-'08 FLST/C/N (ex. '05-'08 FLSTN), '90-'08 FLSTF, '89-'08 FLT (Road Kings and Dressers), '90-'08 Dyna (ex. FXDWG), '89-'00 FXR, and '89-'08 XL.

Tail Light Cover - Clean simplicity has its place; especially on Street Glides or other bikes where the license plate isn’t mounted above the taillight. Without the opening for the license plate light, a cleaner solid visor creates a smoother, flowing look. It’s plated composite material can’t rust & installation requires only two screws. Fits all '73-'08 H-D models without bobbed rear fenders (ex. FLSTN/S/SC, Deuce, & V-Rod).

#4804 (l) & #4803 (r)

Tru-Sphere L.E.D. Bulbs - These are the best L.E.D. replacement bulbs on the market. Each bulb features 32 mega-bright red or 32 super bright amber L.E.D.s in a completely sealed package. Tru-Sphere's unique design provides full hemispherical illumination; you won't believe the improvement over an incandescent bulb. It's dimensions are the same as a standard 1156 incandescent bulb so it can be used as a direct replacement for those applications.

Turn Signal Visors/Grilles

Rear Signal Relocator Bars & Mounts- Moves the rear flashers to the license plate bracket.