ChoptPac installed in Vivid Black w/HighRollers Backrest
ChoptPac on 2015 RoadGlide
ChoptPac assembled in Vivid Black
ChoptPac installed in Vivid Black w/HighRollers Backrest
ChoptPac on 2014 RoadKing w/HD backrest
ChoptPac 2009 StreetGlide w/HD backrest
ChoptPac in Primer
Scootworks ChoptPac- This is our latest addition to the Scootworks TourPack
lineup. These are hand laid & pressed fiberglass, manufactured at our shop. The lids have the extended rain drip of our
SuperTrunk (found further down this page), the interior is sanded and sprayed with a matte black finish, and the lid seal
is installed (on the assembled unit). The bottom is a reinforced flat bottom for installation on any type of mount. We use
our exclusive stainless steel hinges with welded hinge pins, and chrome plated double locking latches on the assembled units,
but you can use H-D latches/hinges if you are converting a stock H-D pack to our chopped version. The lid is secured in the
open position with a lanyard. On the primered version, the exterior is sprayed with a sandable automotive primer. The black
version is manufactured with a Vivid Black gelcoat exterior (NOTE*** this isn't black paint, and while it looks great, may
not be as perfect as a painted / sanded / buffed finish). The chrome top racks listed below in
the SuperTrunk section are compatable with the ChoptTrunk.
These can be purchased 4 ways... #1- as an assembled and ready to paint unit, #2- just the upper/lower (no hardware) for
assembly with your H-D hardware, #3 as just the lower half and your H-D King Tour Pack lid will fit (for conversion to a
ChoptPac if you already have a H-D trunk), #4 in a Vivid Black gelcoat finish & assembled (backrest not included).
Backrests... these do not come with a backrest. We offer the sexy new HighRollers backrest below as an option. You can also install
the H-D factory full size backrest with armrests, the H-D mini-backrest, or the full size Mustang Backrests with armrests
(below).
One of the photos below shows a comparison in height with the standard height SuperTrunk III (same height as the H-D King
Tour Pack). Height at the rear of the ChoptPac is 5-1/2", height at the front is 7", and the max height in the center front is
8".
ChoptPac Variationstm
-> Scootworks ChoptPac - Primered/Assembled $450.00
BUY THIS ITEM
-> Scootworks ChoptPac NO HARDWARE - Primered/Unassembled/Undrilled $375.00
BUY THIS ITEM
-> Scootworks ChoptPac Lower - Primered/Undrilled Bottom Only $200.00
BUY THIS ITEM
-> Scootworks ChoptPac in Vivid Black Gelcoat - assembled $499.99
BUY THIS ITEM
Accessories for the ChoptPactm
Trunk-Mounted Passenger Backrest for Scootworks Tour Pack/Trunk
All parts are hand made right here, in house, in our Zebulon NC shop!
ChoptPac in Vivid Black & HighRollers Backrest on 2015 RoadGlide
SuperTrunktm III - Full Size Motorcycle Trunk
The new flat bottom on our SuperTrunk & CruzPac works great with our mounts, and
is easily fitted to luggage rack mounting and OEM trunk mounts.
Available with plain or studded passenger backrest/armrest combo!
The new HighRollers Custom Mini-Backrest!
Shipped in gelcoat finish, ready for sanding and paint in your color. NOTE- Now shipped
in GLOSS BLACK gel coat!
Beautiful lines, lots of surface area for mounting lights, antenna brackets, etc.
Scootworks SuperTrunk III- Our newest Full-Size motorcycle trunk design! Measures approx. 23" wide,
17.5" front-to-back, and 13" tall. This trunk is proportioned similar to the Harley-Davidson tour
packs found on the Electroglide-series of motorcycles. Add a spacious Tour Pack to your motorcycle
with the Scootworks SuperTrunk III. The Scootworks SuperTrunk III comes in a durable BLACK gel-coat finish,
ready for prep and color matching to your motorcycle. Features lockable latches,
full perimeter lid gasketing, compatable with all H-D and most aftermarket trunk mounts, and instruction manual. This motorcycle trunk is compatable with
all readily available Harley-Davidson accessories to make customization a snap. Our new FLAT BOTTOM is also reinforced
to make installation on luggage racks or installation on our mounting systems found at the
bottom of this page, a snap. As seen in photo link #4 below, it even accepts aftermarket
speaker pods with ease!
SuperTrunk III - Our newest and best looking Full-Size motorcycle trunk!
Trunk/Saddlebag Liner Kit Can also be used to line hard saddlebags, tour packs, toolboxes
or anything that needs a custom-fitted, permanently attached soft liner. Material is pliable
and stretchable to fit into tight corners and over odd shapes. Paper liner allows drawing out
patterns. Can be cut with scissors and trimmed with a utility knife after installation. Adhesive
allows repositioning until it is rubbed down, then it really sticks! Measures 18” x 36”.
Note:
1 kit will cover the bottom of the trunk
2 kits will cover the bottom and sides of the trunk
3 kits will cover the bottom, sides and lid of the trunk
Scootworks SuperTrunk III- This is the same as our black SuperTrunk III above.
These come with a sandable automotive primer coat, reducing the amount of work for your painter. You can purchase this as
body parts only (no hardware), assembled with hinges, locks, latches, and lid stay, or even individual lid and/or bottom.
When purchased as an individual lid, bottom, or unassembled, they come undrilled. This is for many who already have their
own hardware, often with a different bolt pattern.
The lids are the most common part to be damaged in an accident. They are also the most common part to be damaged on the
H-D King Tour Trunk trunk from overloading a top-mounted chrome rack. These fit the H-D King tour pack profile and are
compatible with all H-D King Tour accessories associated with the lid. They are mfg of top quality materials and hand
laid glass.
-> Scootworks SuperTrunk III- Primered/Assembled $449.95
(Note** SuperTrunk III is in an oversize container for product protection, and some shipping charges may apply in the lower 48 states)
BUY THIS ITEM
-> Scootworks SuperTrunk III- Primered/Unassembled/Undrilled $399.95
(Note** SuperTrunk III is in an oversize container for product protection, and some shipping charges may apply in the lower 48 states)
BUY THIS ITEM
-> Scootworks SuperTrunk III Lid- Primered/Undrilled $185.00 BUY THIS ITEM
-> Scootworks SuperTrunk III Bottom- Primered/Undrilled $250.00 BUY THIS ITEM
Scootworks CruzPactm- After
much feedback from customers, developmental work, experimentation, prototype fabrication, and
testing... it's finally here! The Scootworks CruzPac was designed by us for fitment
on mid-size cruisers. Many of our customers have been asking for a smaller trunk for bikes that would
retain the classic styling of our SuperTrunk. Our CruzPactm fits the bill,
coming in at approximately 30% smaller than the SuperTrunk. While most smaller tourpacks have a
more round 'Euro-styling', ours has the classic cruiser styling of our larger trunk, yet in a
smaller package. The Scootworks CruzPac comes in a durable BLACK gel-coat finish, ready for prep and
color matching to your motorcycle.
Pictures 5, 6, & 7 above show the CruzPac with a backrest installed. The CruzPad in pics 5 & 6
matches the typical driver backrest pads found on many cruisers, today. it is available in plain or
studded.
The CruzPac measures approx. 17-1/2" wide at the front and 15-1/2" wide at the rear,
11-1/4" tall at the front and 9-3/4" tall at the rear, and 14.5" front-to-back.
The proportions of this trunk make it perfect for the mid-size cruisers like: Vulcan 800/900,
Honda ACE750/VT1100/VTX1300R, Suzuki Volusia 800/C50, Yamaha 650/1100/1300, and others.
Our new FLAT BOTTOM is also reinforced to make installation on luggage racks or
installation on our mounting systems found at the bottom of the page, a snap.
The Scootworks CruzPactm is supplied with all the features of the
SuperTrunk, including dual locking latches, heavy-duty chrome plated hinges, installed
lid restraint, full perimeter lid seal, reinforced bottom, gelcoat outer finish, and top
quality hand-laid fiberglass construction! Pre-drilled for our WidePad and our standard mounting
footprint of 8" x 6.5".
Trunk/Saddlebag Liner Kit Can also be used to line hard saddlebags, tour packs, toolboxes
or anything that needs a custom-fitted, permanently attached soft liner. Material is pliable
and stretchable to fit into tight corners and over odd shapes. Paper liner allows drawing out
patterns. Can be cut with scissors and trimmed with a utility knife after installation. Adhesive
allows repositioning until it is rubbed down, then it really sticks! Measures 18” x 36”.
-> Lid Seal - 1 Complete Scootworks Trunk Lid Seal Kit $10.99 BUY THIS ITEM
-> Key Kit - 2 Keys for Scootworks Trunks $2.00 BUY THIS ITEM
Motorcycle Trunk Mounting Systems
Early version of Scootworks SuperTrunk II on Nomad 1500 with optional top rack.
Scootworks SuperTrunk III-style tour pack on Kawasaki Nomad 1500
SuperTrunk & Passenger Backrest w/armrests
The SuperTrunk is compatable with aftermarket Speaker Pods!
H-D Heritage with mount installed, ready for a trunk.
Victory Kingpin with a mount and trunk installed
Yamaha RoadStar with a mount and trunk installed
New mount for the H-D Slim!
A pic of a typical mount. These very in shape and design a bit, depending on the bike of fitment.
Motorcycle Trunk Mounting systems - While our
trunks are designed with a flat, reinforced bottom for easy mounting on luggage racks and
other OEM trunk mounts, Scootworks also provides trunk mounting systems for some select motorcycle
makes and models.
Below are the trunk mounts we carry:
--Mounts for Excelsior-Henderson--
->
Custom Trunk Mount Kit for Excelsior-Henderson (1999-2000) - $289.99
BUY THIS ITEM
--Mounts for Harley-Davidson--
->
Custom Trunk Mount Kit for H-D Heritage Softail ('05-'12) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for H-D Softail Custom (tested on '08) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for H-D Slim - $239.99
BUY THIS ITEM
--Mounts for Honda--
->
Custom Trunk Mount Kit for Honda Spirit C-2 - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Honda Aero 750 - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Honda Sabre VT-1100 - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Honda Valkyrie - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Honda VTX1300C - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Honda VTX1300R/S - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Honda VTX1800C - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Honda VTX1800R/S/N - $289.99
BUY THIS ITEM
--Mounts for Kawasaki--
->
Custom Trunk Mount Kit for Vulcan EN500 ('96+) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Vulcan 800 "A" & Classic (all years) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Vulcan 900 Classic LT (mounts to factory sissybar, not fender rails) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Vulcan 900 Custom & Classic, & Classic LT (mounts to fender rails, not compatable with sissybar) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Nomad 1500 and 1500 Classic - $289.99
BUY THIS ITEM
->
Trunk Mount Adapter Kit required for 1500 Classic- $39.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Drifter 1500, SOLO SEAT - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Drifter 1500, DUAL SEAT - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Mean Streak 1500 & 1600 - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Vulcan 1600 Classic (all years) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Nomad 1600 - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Vulcan 1700 Classic - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Vulcan 1700 Classic LT - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Vulcan 1700 Nomad - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Vulcan 1700 Vaquero - $339.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Vulcan VN2000 Classic & LT (mounts to fender rails, not compatable with sissybar)- $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Vulcan VN2000 Classic LT (mounts to factory sissybar, not fender rails) - $289.99
BUY THIS ITEM
--Mounts for Suzuki--
->
Custom Trunk Mount Kit for Volusia 800 (all years) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Boulevard C50 (all years) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Boulevard C50T (all years). Replaces sissybar/luggage rack assy. - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for 1500LC, Boulevard C90, and Boulevard C90T (all years). - $289.99
BUY THIS ITEM
--Mounts for Triumph--
->
Custom Trunk Mount Kit for Thunderbird 2012+ - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Rocket III Std - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Rocket III Touring - $289.99
BUY THIS ITEM
--Mounts for Victory--
->
Custom Trunk Mount Kit for Victory Kingpin (all years) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Victory Vegas - $289.99
BUY THIS ITEM
--Mounts for Yamaha--
->
Custom Trunk Mount Kit for Yamaha V-Star 650 (all years) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Yamaha V-Star 950 Classic - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Yamaha V-Star 950 Custom - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Yamaha V-Star 1100 Classic - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Yamaha V-Star 1100 Custom - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Yamaha V-Star 1300 NOTE* Silverado requires different bolts, specify in comments section of order - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Yamaha V-Star 1300 Tourer - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Yamaha Royal Star Tour Deluxe - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Yamaha Roadstar 1600/1700 (all years) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Yamaha Roadliner (all years) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Yamaha Stratoliner (all years) - $289.99
BUY THIS ITEM
->
Custom Trunk Mount Kit for Yamaha Raider & Raider-S - $289.99
BUY THIS ITEM
*Scootworks products are protected by patent pending,
US/International patents, and/or intellectual property rights. Reproduction without
express written permission from Scootworks is forbidden and will be prosecuted to the fullest
extent of the law.